Alloy Steel Supplier in Bawal

Product Details:

Steel C45 Round Bar is an unalloyed medium carbon steel, which is also a general carbon engineering steel. C45 is a medium strength steel with good machinability and excellent tensile properties. C45 round steel is generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 – 700 Mpa and Brinell hardness range 170 – 210 in either condition. It does not however respond satisfactorily to nitriding due to a lack of suitable alloying elements.

Product Details:

EN8 carbon steel is a common medium carbon and medium tensile steel, with improved strength over mild steel, through-hardening medium carbon steel. EN8 carbon steel is also readily machinable in any condition.

EN8 steels are generally used in the as supplied untreated condition. But EN8 steels can be further surface-hardened by induction processes, producing components with enhanced wear resistance. Steel EN8 materials in its heat treated forms possesses good homogenous metallurgical structures, giving consistent machining properties.

4.1 Carbon Steel EN8 Chemical Composition

4.2 EN8 Medium Carbon Steel Mechanical Properties and Hardness

 

Product Details:

Features:

• Crank shafts, automobile axle beams, connecting rods, Lightly stressed gears
• Generally used for moderately stressed parts of Motor Vehicles and general engineering works

Additional Information:

• Delivery Time: READY STOCK

Product Details:

Carbon steels are iron-carbon alloys containing up to 2.06% of carbon, up to 1.65% of manganese, up to 0.5% of silicon and sulfur and phosphorus as impurities.

Carbon content in carbon steel determines its strength and ductility.

The higher carbon content, the higher steel strength and the lower its ductility.

According to the steels classification there are following groups of carbon steels:

• Low carbon steels (C < 0.25%)
• Medium carbon steels (C =0.25% to 0.55%)
• High carbon steels (C > 0.55%)
  • Tool carbon steels (C>0.8%)

Product Details:

Carbon steel is available as bright drawn key steel in flat and square sections. With medium tensile strength key steel is used widely in general engineering for components such as plain, gibhead, taper and parallel keys. Key steel is produced to the required tolerances as specified in British Standard BS46

Product Details:

West Yorkshire Steel are suppliers of H13 Hot Die Steel in square bar, diameters and plate, cut to your requirements. As a reliable hot work steel it is suitable for a wide variety of applications. It combines very good red-hardness with toughness and tools may be water-cooled in service. H13 may be cold-hobbed in the annealed condition.

Additional Information:

• Delivery Time: READY STOCK

Product Details:

AISI D2 steel is an air and oil hardening cold work tool steel, D2 Steel Composition, Chemical composition of steel, D2 Die Steel

which offer great dimensional stability during heat treatment with good hardness and abrasion resistance.

It is normally supplied in annealed condition. 

The main application of  D2 die steel based on the type of required work is as follows :-

 

• Forming rolls, D2 Steel Composition, Chemical composition of steel, D2 Die Steel
• Tools, Molds for plastic mold industries,
• Punches, D2 Steel Composition, Chemical composition of steel, D2 Die Steel
• Knives, die steel composition, steel composition, density of high carbon steel, d2 alloy steel, tool
• Shear blades, die steel composition, steel composition, density of high carbon steel, d2 alloy steel, tool
• Stamping dies and die steel composition, steel composition, density of high carbon steel, d2 alloy steel, tool
• Blanking dies.

Price Range - Rs 300 - Rs 600

Product Details:

AISI H11 tool steel is a 5% chromium hot work tool steel that is represented by its excellent impact toughness. Chromium hot-work tool steels are designated as group H steels according to the AISI classification system, and specified in ASTM A681standard. The most commonly used chromium hot-work steels are H11 tool steel, h12 tool steel, and H13 steel, within the series from H1 to H19.

If we compare between H11 and H13, H11 tool steel consists of less vanadium than the commonly used H13 hot work tool steel. This gives H11 steels the higher toughness, with some reduction in wear resistance and temper resistance. H11 tool steel is a deep-hardening, air-hardening steel and H11 alloy steel could be deep hardened by heat treatment and air-quenching. That gives minimal size change during heat treatment. H11 how work steel also has super resistance to thermal fatigue cracking and superb resistance to gross cracking and thermal shock when water cooled in service.

Additional Information:

• Delivery Time: READY STOCK

Product Details:

H-11 steels are the most commonly used Hot Die Tool Steels. These Hot Die Steels made up of the composition of various grades like Carbon, Mangnese, Silicon, Chromium. Chromium is the major chemical composition of H-11 tool steels. It contains 4.75-5.50% Chromium. It can be air hardened in 150 mm thick sections.These steels have minimal distortion during hardening due to their balanced alloy content.These steels can be cooled using water without damage. These steels have low Carbon and alloy contents with good toughness. These steels can be deep hardened by heat treatment and air-quenching.

APPLICATIONS

The Hot Die Steels (H-11 Steels) are widely used in-
i. Forging dies
ii. Die casting
iii. Bolt dies
iv. Hot piercing punches
v. Shrink rings
vi. Moulds
vii. Metal extrusion tools for processing light metals
viii. Screws and barrels for plastic processing etc.

FEATURES:

i. Durable
ii. Fine finishing
iii. Can be water-cooled to a limited extent
iv. Unmatched thermal conductivity
v. Insusceptibility to hot cracking etc.

Product Details:

West Yorkshire Steel are suppliers of H13 Hot Die steel in round bar, diameters and plate, cut to your requirements. As a reliable hot work steel it is suitable for a wide variety of applications. It combines very good red-hardness with toughness and tools may be water-cooled in service. H13 may be cold-hobbed in the annealed condition.

Additional Information:

• Delivery Time: READY STOCK

Product Details:

AISI H11 tool steel is a 5% chromium hot work tool steel that is represented by its excellent impact toughness. Chromium hot-work tool steels are designated as group H steels according to the AISI classification system, and specified in ASTM A681standard. The most commonly used chromium hot-work steels are H11 tool steel, h12 tool steel, and H13 steel, within the series from H1 to H19.

Product Details:

H-11 steels are the most commonly used Hot Die Tool Steels. These Hot Die Steels made up of the composition of various grades like Carbon, Mangnese, Silicon, Chromium. Chromium is the major chemical composition of H-11 tool steels. It contains 4.75-5.50% Chromium. It can be air hardened in 150 mm thick sections.These steels have minimal distortion during hardening due to their balanced alloy content.These steels can be cooled using water without damage. These steels have low Carbon and alloy contents with good toughness. These steels can be deep hardened by heat treatment and air-quenching.

Product Details:

Alloy steels contain different varieties of steels that exceed the composition limits of Mn, C, Mo, Si, Ni, Va, and B set for carbon steels. They are designated by AISI four-digit numbers. They respond more quickly to mechanical and heat treatments than carbon steels.AISI 52100 alloy steel is known as a high carbon, chromium containing low alloy steel. The following datasheet gives an overview of AISI 52100 alloy steel.

Product Details:

AISI 4340 steel is a medium carbon, low alloy steel known for its toughness and strength in relatively large sections. AISI 4340 is also one kind of nickel chromium molybdenum steels. 4340 alloy steel is generally supplied hardened and tempered in the tensile range of 930 – 1080 Mpa. Pre hardened and tempered 4340 steels can be further surface hardened by flame or induction hardening and by nitriding. The 4340 steel has good shock and impact resistance as well as wear and abrasion resistance in the hardened condition. AISI 4340 steel properties offer good ductility in the annealed condition, allowing it to be bent or formed. Fusion and resistance welding is also possible with our 4340 alloy steel. ASTM 4340 material is often utilized where other alloy steels do not have the hardenability to give the strength required. For highly stressed parts it is excellent choice. AISI 4340 alloy steel can also be machined by all customary methods.

Additional Information:

• Delivery Time: READY STOCK

Product Details:

EN8 carbon steel is a common medium carbon and medium tensile steel, with improved strength over mild steel, through-hardening medium carbon steel. EN8 carbon steel is also readily machinable in any condition.

EN8 steels are generally used in the as supplied untreated condition. But EN8 steels can be further surface-hardened by induction processes, producing components with enhanced wear resistance. Steel EN8 materials in its heat treated forms possesses good homogenous metallurgical structures, giving consistent machining properties.

4.1 Carbon Steel EN8 Chemical Composition

4.2 EN8 Medium Carbon Steel Mechanical Properties and Hardness

 

Product Details:

EN24 is a very high strength steel alloy which is supplied hardened and tempered. 

The grade is a nickel chromium molybdenum combination - this offers high tensile steel strength, with good ductility and wear resistance characteristics. With relatively good impact properties at low temperatures, EN24 is also suitable for a variety of elevated temperature applications
. 
EN24 Engineering Steel is easy to treat and temper and is supplied hardened and tempered. The alloy offers a good combination of strength, ductility and wear resistance. It is a very high strength alloy engineering steel.

Product Details:

Carbon steels are iron-carbon alloys containing up to 2.06% of carbon, up to 1.65% of manganese, up to 0.5% of silicon and sulfur and phosphorus as impurities.

Carbon content in carbon steel determines its strength and ductility.

The higher carbon content, the higher steel strength and the lower its ductility.

According to the steels classification there are following groups of carbon steels:

• Low carbon steels (C < 0.25%)
• Medium carbon steels (C =0.25% to 0.55%)
• High carbon steels (C > 0.55%)
  • Tool carbon steels (C>0.8%)

Additional Information:

• Delivery Time: READY STOCK

Product Details:

EN 353 steel has carbon content material of 0.17 % & probably the most usual form of steel, because the carbon content material raises, the material becomes tougher & harder. It's observed that the hardness & wear resistance of the EN 353 steels elevated after the warmness therapy & the micro structure is exchange from ferrite to marten website.
This grade is in general used for a lot of automobiles functions comparable to heavy duty tools, shaft, pinion, cam shafts and gudgeon pins.

Steel Properties

En 353 steel has a carbon content of 0.17% and the commonest form of steel as it provides material properties that are acceptable for several automobile applications such as significant duty gear, shaft, pinion, camshafts and gudgeon pins. It’s neither outwardly brittle nor ductile due to its lower carbon content and lower hardness. Because the carbon content will increase, the metal becomes more durable and stronger.

Product Details:

EN8 carbon steel is a common medium carbon and medium tensile steel, with improved strength over mild steel, through-hardening medium carbon steel. EN8 carbon steel is also readily machinable in any condition.

EN8 steels are generally used in the as supplied untreated condition. But EN8 steels can be further surface-hardened by induction processes, producing components with enhanced wear resistance. Steel EN8 materials in its heat treated forms possesses good homogenous metallurgical structures, giving consistent machining properties.

Good heat treatment results on sections larger than 65mm may still be achievable, but it should be noted that a fall-off in mechanical properties would be apparent approaching the centre of the bar. It is therefore recommended that larger sizes of EN8 steel materials are supplied in the untreated condition, and that any heat treatment is carried out after initial stock removal. This should achieve better mechanical properties towards the core.

Carbon Steel EN8 Chemical Composition

 

Product Details:

West Yorkshire Steel are suppliers of H13 Hot Die steel in round bar, diameters and plate, cut to your requirements. As a reliable hot work steel it is suitable for a wide variety of applications. It combines very good red-hardness with toughness and tools may be water-cooled in service. H13 may be cold-hobbed in the annealed condition.